Differences between revisions 3 and 14 (spanning 11 versions)
⇤ ← Revision 3 as of 2020-06-22 16:03:46 →
Size: 1604
Editor: DominicRicottone
Comment:
← Revision 14 as of 2023-01-08 20:24:15 → ⇥
Size: 1868
Editor: DominicRicottone
Comment:
Deletions are marked like this. Additions are marked like this.
Line 2: Line 2:

'''Alpine Linux''' is a Linux-based operating system. It is distinguished from other distributions by its dedication to minimalism. It is ideal for containerized deployments.
Line 9: Line 11:
== Create Bootable Device == == Installation ==
Line 11: Line 13:
The Alpine Linux wiki recommends use of `fdisk`. For more general advice regarding partitioning, see [[PartitionTablesSetup|here]]. Insert the target device and ensure it is not mounted. (If it is, try `umount /dev/sdXN`.)
Line 13: Line 15:
First and foremost, insert the device and ensure it is not mounted. (If it is, `umount /dev/sdXN`.) Secondly, ensure that the device is '''not''' using a GPT partition table. This would be listed by 'Disklabel type' in `fdisk`. The correct value is `dos`, not `gpt`.

Per the [[https://wiki.alpinelinux.org/wiki/Create_a_Bootable_USB#Format_USB_stick|wiki]]:

 * Run fdisk on your device (`sdX`).		 Upstream recommends use of `fdisk(8)`. The partitioning process is as follows:
Line 23: Line 21:
 * Create new partition table with one FAT32 partition  1. Ensure that the device is ''not'' using a GPT partition table. This would be listed under ''Disklabel type''. ''(Press `p` to list the partitions.)'' The correct value is `dos`, not `gpt`.
 2. Create new partition table with one FAT32 partition
   1. `d` Delete all partitions (and repeat as needed)
   2. `n` Create a new partition
   3. `p` A primary partition
   4. `1` Partition number 1
   5. Use defaults for first and last cylinder (press [Enter] twice).
   6. `t` Change partition type
   7. `c` Partition type (Win95 FAT32/LBA)
 3. Ensure that the primary partition is bootable. This is marked by an asterisk (`*`). ''(Press `p` to list the partitions.)'' To make the partition bootable...
   1. `a` Set the boot flag on a partition
   2. `1` Partition number 1
 4. `w` Write your changes to the device
Line 25: Line 35:
  1. `d` Delete all partitions (this may take a few steps) For more general advice regarding partitioning, see [[Linux/PartitionTables|here]].
Line 27: Line 37:
  2. `n` Create a new partition

  3. `p` A primary partition

  4. `1` Partition number 1

  5. Use defaults for first and last cylinder (just press [Enter] twice).

  6. `t` Change partition type

  7. `c` Partition type (Win95 FAT32/LBA)

 * Verify that the primary partition is bootable

  1. `p` Print list of partitions

  2. If there is no '*' next to the first partition, follow the next steps:

  3. `a` Make the partition bootable (set boot flag)

  4. `1` Partition number 1

 * `w` Write your changes to the device

 * Format the new partition with:		 Format the new partition with:
Line 57: Line 43:
Note that [[FileSystemSetup#MS-DOS|mkfs.vfat and mkdosfs are the same]]. Note that [[Linux/FileSystems#MS-DOS|mkfs.vfat and mkdosfs are the same]].
Line 59: Line 45:
Finally, `dd` the ISO onto the device. Or for a Raspberry Pi, copy the boot binaries onto the device. Finally, `dd(1)` the ISO onto the device. Or for a Raspberry Pi, copy the boot binaries onto the device.

----



== Administration ==

 * [[Linux/Alpine/Apk|apk]]
 * [[Linux/OpenRC|OpenRC]]



== Design ==

 * [[Linux/Alpine/Packaging|packaging system]]
 * [[Linux/Alpine/Storage|storage system]]

Alpine Linux

Alpine Linux is a Linux-based operating system. It is distinguished from other distributions by its dedication to minimalism. It is ideal for containerized deployments.

Contents

  1. Alpine Linux
    1. Installation
    2. Administration
    3. Design

Installation

Insert the target device and ensure it is not mounted. (If it is, try umount /dev/sdXN.)

Upstream recommends use of fdisk(8). The partitioning process is as follows: 

fdisk /dev/sdX

  1. Ensure that the device is not using a GPT partition table. This would be listed under Disklabel type. (Press p to list the partitions.) The correct value is dos, not gpt.

  2. Create new partition table with one FAT32 partition

    1. d Delete all partitions (and repeat as needed)

    2. n Create a new partition

    3. p A primary partition

    4. 1 Partition number 1

    5. Use defaults for first and last cylinder (press [Enter] twice).

    6. t Change partition type

    7. c Partition type (Win95 FAT32/LBA)

  3. Ensure that the primary partition is bootable. This is marked by an asterisk (*). (Press p to list the partitions.) To make the partition bootable...

    1. a Set the boot flag on a partition

    2. 1 Partition number 1

  4. w Write your changes to the device

For more general advice regarding partitioning, see here.

Format the new partition with: 

mkfs.vfat /dev/sdX1

Note that mkfs.vfat and mkdosfs are the same.

Finally, dd(1) the ISO onto the device. Or for a Raspberry Pi, copy the boot binaries onto the device.

Administration

Design

CategoryRicottone

Linux/Alpine (last edited 2023-01-08 20:24:15 by DominicRicottone)